# $OpenLDAP$
# Copyright 2021-2022 The OpenLDAP Foundation, All Rights Reserved.
# COPYING RESTRICTIONS APPLY, see COPYRIGHT.
H1: Load Balancing with lloadd

As covered in the {{SECT:Replication}} chapter, replication is a fundamental
requirement for delivering a resilient enterprise deployment.  As such
there's a need for an LDAPv3 capable load balancer to spread the load between the
various directory instances.

{{lloadd}}(8) provides the capability to distribute LDAP v3 requests between a
set of running {{slapd}} instances.  It can run as a standalone daemon
{{lloadd}}, or as an embedded module running inside of {{slapd}}.

H2: Overview

{{lloadd}}(8) was designed to handle LDAP loads.
It is protocol-aware and can balance LDAP loads on a per-operation basis rather
than on a per-connection basis.

{{lloadd}}(8) distributes the load across a set of slapd instances. The client
connects to the load balancer instance which forwards the request to one
of the servers and returns the response back to the client.

H2: When to use the OpenLDAP load balancer

In general, the OpenLDAP load balancer spreads the load across configured backend servers.  It does not perform
so-called intelligent routing. It does not understand semantics behind the operations being performed by the clients.

More considerations:

 - Servers are indistinguishable with respect to data contents.  The exact same copy of data resides on every server.
 - Clients do not require 'sticky' sessions.
 - The sequence of operations isn't important.  For example, read after update isn't required by the client.
 - If your client can handle both connection pooling and load distribution then it's preferable to lloadd.
 - Clients that require a consistent session (e.g. do writes), the best practice is to let them set up a direct session to one of the providers.  The read-only clients are still free to use lloadd.
 - 2.6 release of lloadd will include sticky sessions (coherency).

H2: Runtime configurations

It deploys in one of two ways:

^ Standalone daemon: {{ lloadd }}
+ Loaded into the slapd daemon as a module: {{ lloadd.la }}

It is recommended to run with the balancer module embedded in slapd because dynamic configuration (cn=config) and the monitor backend are then available.

{{B: Sample load balancer scenario:}}

!import "load-balancer-scenario.png"; align="center"; title="Load Balancer Scenario"
FT[align="Center"] Figure: Load balancer sample scenario

^ The LDAP client submits an LDAP operation to
the load balancer daemon.

+ The load balancer forwards the request to one of the backend instances in its pool of servers.

+ The backend slapd server processes the request and returns the response to
the load balancer instance.

+ The load balancer returns the response to the client.  The client's unaware that it's connecting to a load balancer instead of slapd.

H2: Build Notes

To build the load balancer from source, follow the instructions in the
{{SECT: A Quick-Start Guide}} substituting the following commands:

^ To configure as standalone daemon:

..{{EX:./configure --enable-balancer=yes}}

+ To configure as embedded module to slapd:

..{{EX:./configure --enable-modules --enable-balancer=mod}}

H2: Sample Runtime

^ To run embedded as {{ lloadd }} module:

..{{EX: slapd [-h URLs]  [-f lloadd-config-file] [-u user] [-g group]}}

 - the startup is the same as starting the {{ slapd }} daemon.
 - URLs is for slapd management. The load balancer's listener URLs set in the configuration file or node. (more later)

+ To run as standalone daemon:

..{{EX: lloadd [-h URLs]  [-f lloadd-config-file] [-u user] [-g group]}}

 - Other than a different daemon name, running standalone has the same options as starting {{ slapd }}.
 - -h URLs specify the lloadd's interface directly, there is no management interface.

For a complete list of options, checkout the man page {{ lloadd.8 }}

H2: Configuring load balancer

H3: Common configuration options

Many of the same configuration options as slapd. For complete list, check
the {{lloadd}}(5) man page.

.{{S: }}
{{B:Edit the slapd.conf or cn=config configuration file}}.

To configure your working {{lloadd}}(8) you need to make the following changes to your configuration file:
  ^ include {{ core.schema }} (embedded only)
  + {{ TLSShareSlapdCTX { on | off } }}
  + Other common TLS slapd options
  + Setup argsfile/pidfile
  + Setup moduleload path (embedded mode only)
  + {{ moduleload      lloadd.la }}
  + loglevel, threads, ACL's
  + {{ backend lload }} begin lloadd specific backend configurations
  + {{ listen ldap://:PORT }} Specify listen port for load balancer
  + {{ feature proxyauthz }} Use the proxy authZ control to forward client's identity
  + {{ io-threads INT }} specify the number of threads to use for the connection manager.  The default is 1 and this is typically adequate for up to 16 CPU cores

H3: Sample backend config

Sample setup config for load balancer running in front of four slapd instances.

>backend lload
>
># The Load Balancer manages its own sockets, so they have to be separate
># from the ones slapd manages (as specified with the -h "URLS" option at
># startup).
>listen ldap://:1389
>
># Enable authorization tracking
>feature proxyauthz
>
># Specify the number of threads to use for the connection manager.  The default is 1 and this is typically adequate for up to 16 CPU cores.
># The value should be set to a power of 2:
>io-threads  2
>
># If TLS is configured above, use the same context for the Load Balancer
># If using cn=config, this can be set to false and different settings
># can be used for the Load Balancer
>TLSShareSlapdCTX true
>
># Authentication and other options (timeouts) shared between backends.
>bindconf bindmethod=simple
>         binddn=dc=example,dc=com credentials=secret
>         network-timeout=5
>         tls_cacert="/usr/local/etc/openldap/ca.crt"
>         tls_cert="/usr/local/etc/openldap/host.crt"
>         tls_key="/usr/local/etc/openldap/host.pem"
>
>
># List the backends we should relay operations to, they all have to be
># practically indistinguishable. Only TLS settings can be specified on
># a per-backend basis.
>
>backend-server uri=ldap://ldaphost01 starttls=critical retry=5000
>               max-pending-ops=50 conn-max-pending=10
>               numconns=10 bindconns=5
>backend-server uri=ldap://ldaphost02 starttls=critical retry=5000
>               max-pending-ops=50 conn-max-pending=10
>               numconns=10 bindconns=5
>backend-server uri=ldap://ldaphost03 starttls=critical retry=5000
>               max-pending-ops=50 conn-max-pending=10
>               numconns=10 bindconns=5
>backend-server uri=ldap://ldaphost04 starttls=critical retry=5000
>               max-pending-ops=50 conn-max-pending=10
>               numconns=10 bindconns=5
>
>#######################################################################
># Monitor database
>#######################################################################
>database        monitor
